Anti-Jamming

GNSS Interference Maps: Read the Evidence

Stan Zhu·May 21, 2026Updated Oct 27, 2026·4 min read
Conceptual GNSS signal disruption illustration; not a measured interference map or geographic risk ranking.

GNSS interference maps can help a civilian survey team decide where to investigate, but they cannot predict whether a particular antenna and receiver will work at a site. Most public maps summarize observations from other platforms, at other heights and over an aggregation period. They are evidence of reported conditions, not a local RF specification.

Use them to prepare questions for a site survey. A blank area does not prove clean reception, a colored area does not identify an emitter, and a persistent color does not establish the probability of failure for your equipment.

What public GNSS interference maps actually measure

A map title may say “jamming,” while the underlying observation is a navigation-quality indicator. That difference matters. Before interpreting a cell, find the provider’s method and identify the raw observable, platform population, time window and coverage limitations.

The GPSJAM FAQ explains that its map aggregates aircraft navigation-accuracy reports from ADS-B. The provider cautions that low reported accuracy does not by itself identify the cause. Aircraft observations also cannot be transferred directly to a ground receiver, and absent cells may reflect absent observations rather than verified conditions.

Other tools may use position anomalies or dedicated RF sensors. Their outputs answer different questions. A position jump can motivate a spoofing investigation without proving its mechanism; a spectrum observation can establish unwanted energy without proving the resulting position error.

Public evidence What it can contribute What still needs checking
Aircraft navigation-quality map A spatial and temporal summary of reported navigation quality Cause, altitude differences and relevance to your receiver
Position-anomaly analysis Candidate events for consistency checks Detector assumptions, data errors and independent confirmation
Dedicated RF monitoring Observed energy at a sensor location and time Calibration, bandwidth, coverage and effect on your equipment
Official operational notice A published condition or planned activity Valid period, area, platform scope and current status

Do not combine these into a single incident count unless the definitions and overlaps have been resolved.

Build a small evidence record before drawing conclusions

Save the observation date and retrieval date separately. Record the time zone, map layer, aggregation interval and the provider’s current method. If the provider changes its network or detector, a change in map appearance may reflect observation coverage rather than a change in the RF environment.

Keep the original link and any permitted export with its legend. Annotate whether a location represents a receiving platform, an affected grid cell or an independently estimated source. Those are different spatial claims. The place where a receiver reported trouble is not automatically the origin of interference.

For a proposed trend comparison, ask whether the same observable, thresholds and coverage apply throughout the period. Check missing days and platform-count changes. Without that work, avoid statements that incidents doubled, that one region is the highest risk or that a particular season predicts future conditions.

This article supplies a reading and planning method. It does not offer a global risk ranking, a multi-year incident series or a forecast.

Translate the map into a local survey plan

Define the task before collecting RF data: a fixed reference station, a coastal rover route and an inspection drone operate at different heights, orientations and equipment states. List the locations and periods that matter to the work, including startup, turns, transmitter use and correction-link interruptions.

Then collect a baseline with the intended receiver, antenna and cable path. Record tracked signals, per-signal carrier-to-noise density, RF monitor indicators, raw observations where available, correction age and solution states. Include nearby equipment activity and relevant changes in sky view.

A fixed RTK state is a useful diagnostic, but position validation needs an independent reference with a stated uncertainty. Where there is no suitable independent check, record that limit rather than converting receiver confidence into demonstrated accuracy.

Repeat observations across representative operating periods. A quiet visit establishes only what happened during that visit. A public map showing previous degradation is a reason to broaden the observation plan, not a substitute for those measurements.

Separate external RF problems from the installation

Before assigning a local event to a regional map, inspect antenna power, connector condition, cable routing and correction delivery. Toggle onboard or site electronics where safe and practical. Check whether the symptom tracks one equipment state, one direction or one physical cable position.

A problem that follows a power converter may need source suppression or rerouting. An outage behind a structure may need a different antenna location or operating procedure. See the GNSS EMI diagnostic workflow for a controlled way to compare those changes.

Jamming and spoofing also cannot be identified solely from a map color. The GNSS jamming versus spoofing guide explains why tracking and solution symptoms can overlap.

Let measured failure modes guide mitigation

Band coverage should match the receiver’s actual signals. Additional frequencies or constellations can provide useful observations, but they are not independent guarantees against a shared front-end problem. A stronger amplifier is also not a general remedy for overload.

Spatial processing may help with some directional interference when the array, processor and receiver are compatible. It does not provide automatic signal authentication or guarantee valid positioning. Require configuration-specific evidence and acceptance tests rather than choosing array size from a regional map.

For a procurement review, prepare a short record: intended task, affected signals, observed symptoms, installation drawing, receiver logs and required fallback behavior. Include the public-map observations as context with their limitations clearly labeled.

Share that installation and evidence record with GNSource when requesting antenna options. It supports a concrete discussion of band coverage, RF-chain compatibility and validation work without treating a public observation map as a product performance guarantee.

Need help choosing the right antenna?

Tell us your platform, bands, environment, and accuracy target — our engineers respond within 24 hours.

Talk to our engineers