Survey equipment
For an external survey receiver, compare the required signals, antenna weight and mounting position. Include the cable and mating connector in the equipment layout rather than choosing the antenna from gain alone.

Compact active external GNSS antenna
For geodetic and marine surveying, precision agriculture and deformation-monitoring equipment. Match the selected signals and mechanical interface to your receiver and installation.
TDXL-BA720 is a compact active external GNSS antenna with a TNC-K connection. Its listed frequency range is 1205–1278 MHz · 1559–1615 MHz. Compare its signal selection with your receiver and plan external mounting and the RF cable as one installation.
| Listed signal selection | BDS B1I/B1C/B2b/B3I · GPS L1/L2 · GLONASS G1/G2 · Galileo E1/E5b |
|---|---|
| Operating frequency | 1205–1278 MHz · 1559–1615 MHz |
| Impedance | 50 Ω |
| Polarization | RHCP |
| Maximum antenna gain | ≥4.5 dBi |
| Axial ratio | ≤3 dB |
| Horizontal coverage | 360° |
| Phase center error | ≤2 mm |
| LNA gain | 34 ± 2 dB |
| Noise figure | ≤2 dB |
| In-band flatness | ±2 dB |
| Operating voltage | 3–12 V DC |
| Current draw | ≤40 mA |
| Dual-frequency delay difference | ≤5 ns |
| Output VSWR | ≤2:1 |
| Operating temperature | −40°C to +80°C |
| Storage temperature | −45°C to +85°C |
| Humidity, non-condensing | 95% RH |
| Connector | TNC-K |
| Weight | ≤180 g |
| Dimensions | Ø100 ± 1 mm × 60.30 ± 1 mm |
Start with the measurement task, then match the receiver, antenna format and installation. These project contexts help define the configuration to evaluate.
For an external survey receiver, compare the required signals, antenna weight and mounting position. Include the cable and mating connector in the equipment layout rather than choosing the antenna from gain alone.
For agricultural equipment or marine surveying, describe the moving platform, antenna orientation and cable routing. Evaluate reception and measurement performance with the intended receiver and installation in the project’s operating conditions.
List the receiver model, required GNSS signals and correction method. Match these against the model’s signal selection; a shared constellation name alone does not establish support for every signal.
Check the receiver’s antenna bias voltage and available current against this model’s electrical specifications. Include cable voltage drop and antenna-detection behavior in the RF-chain review.
Specify cable type, length and the exact mating connector. Review cable losses with the receiver input range and any amplification in the RF chain. Antenna gain alone does not define a maximum cable length.
Include the mounting drawing, orientation and available clearance. For an embedded assembly, include the enclosure and cable exit; for an external antenna, include the support and exposed connections.
Compare the actual signal selection and installation format, not the model number alone.
Lightweight active embedded GNSS antenna. Compare an embedded MCX assembly when the antenna must sit inside your equipment enclosure; include its installed clearance.
Multi-frequency active external GNSS antenna. Compare the external active format by signals, power requirements and connector before selecting the mounting arrangement.
Broadband active embedded GNSS antenna. Compare an embedded MCX assembly when the antenna must sit inside your equipment enclosure; include its installed clearance.
The antenna is one part of the positioning system. RTK operation and accuracy depend on the receiver, correction data, installation and operating conditions. Specify the full system and accuracy target when requesting a model recommendation.
Compare the exact signals, antenna-port electrical requirements and mating connector. Review the complete RF gain and cable losses with the receiver’s input range. A matching connector alone is not enough to select an antenna.
Send the model, receiver, required signals, cable length, connector, mounting drawing and quantity. Include calibration or environmental requirements and your sample evaluation schedule so the configuration can be discussed before ordering.
Describe the required cable assembly, connector and installation envelope. OEM/ODM work is reviewed on the existing platform for each project. Agree the electrical and mechanical configuration and sample evaluation requirements before a production order.
Get a Quote
Share your receiver model, bias voltage, required signals, cable length, connector, enclosure and quantity. We can review deeper customization on the existing platform; feasibility is confirmed for each project.