Reference stations
For a reference-station project, define the receiver signals, antenna position and mounting arrangement together. Include any antenna calibration requirements and the cable route to the receiver in the selection brief.

Civil multi-band active external GNSS antenna
For surveying, deformation monitoring and reference-station projects. Check the antenna calibration and installation requirements of your network before selection.
TDXL-BA802 is a civil multi-band active external GNSS antenna with a TNC-K connection. Its listed frequency range is 1164–1300 MHz · 1525–1621 MHz. Compare its signal selection with your receiver and plan external mounting and the RF cable as one installation.
| Listed signal selection | BDS B1I/B1C/B2a/B2b/B3I · GPS L1/L2/L5 · GLONASS G1/G2/G3 · Galileo E1/E5a/E5b/E6 |
|---|---|
| Operating frequency | 1164–1300 MHz · 1525–1621 MHz |
| Impedance | 50 Ω |
| Polarization | RHCP |
| Antenna gain at zenith | ≥5 dBi |
| Axial ratio at zenith | ≤1.5 dB |
| Horizontal coverage | 360° |
| Phase center error | ±2 mm |
| LNA gain | 35 ± 2 dB |
| Noise figure | ≤2 dB |
| In-band flatness | ±2 dB |
| Operating voltage | 3–16 V DC |
| Current draw | ≈45 mA |
| Group delay | ≤5 ns |
| Output VSWR | ≤2:1 |
| Operating temperature | −40°C to +85°C |
| Storage temperature | −45°C to +85°C |
| Humidity, non-condensing | 95% RH |
| Connector | TNC-K |
| Weight | ≤350 g |
| Dimensions | Ø130 ± 0.50 mm × 57.30 ± 1 mm |
| Mounting interface | 5/8-11 |
| Ingress protection | IP67 |
Start with the measurement task, then match the receiver, antenna format and installation. These project contexts help define the configuration to evaluate.
For a reference-station project, define the receiver signals, antenna position and mounting arrangement together. Include any antenna calibration requirements and the cable route to the receiver in the selection brief.
For monitoring a fixed point, plan a stable mount and a repeatable antenna position. Specify the observation schedule, receiver and correction method so the complete measurement system can be evaluated for the project.
List the receiver model, required GNSS signals and correction method. Match these against the model’s signal selection; a shared constellation name alone does not establish support for every signal.
Check the receiver’s antenna bias voltage and available current against this model’s electrical specifications. Include cable voltage drop and antenna-detection behavior in the RF-chain review.
Specify cable type, length and the exact mating connector. Review cable losses with the receiver input range and any amplification in the RF chain. Antenna gain alone does not define a maximum cable length.
Include the mounting drawing, orientation and available clearance. For an embedded assembly, include the enclosure and cable exit; for an external antenna, include the support and exposed connections.
Compare the actual signal selection and installation format, not the model number alone.
Broadband active external GNSS antenna. Compare the external active format by signals, power requirements and connector before selecting the mounting arrangement.
Broadband active embedded GNSS antenna. Compare an embedded MCX assembly when the antenna must sit inside your equipment enclosure; include its installed clearance.
Passive broadband GNSS antenna. Compare the passive format only with a separately planned RF chain; it is not interchangeable with an active antenna.
The antenna is one part of the positioning system. RTK operation and accuracy depend on the receiver, correction data, installation and operating conditions. Specify the full system and accuracy target when requesting a model recommendation.
Compare the exact signals, antenna-port electrical requirements and mating connector. Review the complete RF gain and cable losses with the receiver’s input range. A matching connector alone is not enough to select an antenna.
Send the model, receiver, required signals, cable length, connector, mounting drawing and quantity. Include calibration or environmental requirements and your sample evaluation schedule so the configuration can be discussed before ordering.
Describe the required cable assembly, connector and installation envelope. OEM/ODM work is reviewed on the existing platform for each project. Agree the electrical and mechanical configuration and sample evaluation requirements before a production order.
Get a Quote
Share your receiver model, bias voltage, required signals, cable length, connector, enclosure and quantity. We can review deeper customization on the existing platform; feasibility is confirmed for each project.